Melt & Pour Glycerine Base White - 1kg

In stock

SKU

mpwb1

R 90.00

White Melt and Pour Soap is so easy to use. Just melt, customize with your favorite colors and scents, and pour into a mold. Colors really pop in this base.

Details

White Glycerine soap. Made with high-quality ingredients, our soap base is the ultimate DIY solution for those looking to create their own all-natural soap bars, without the need for complicated recipes or extensive experience.

Taste: N/A
Odour: Neutral
Colour: White
pH: 6.5 – 7
Melting Point: 60 degrees Celsius
Solubility: Water-soluble
Physical State & Appearance: Semi-hard, white. Wrapped in plastic film (1kg block)

Product Information

Ph-Balanced
Hypo-Allergenic
Strong lathering properties
Strong Moisturising properties
Contains no animal products
Contains no harmful chemicals
Note: Always be cautious when working with melted bases. Keep out of reach of children & pets. Own testing / recipes is required.

How to Use

Cut off enough soap base to fill your mould. (You can either fill your mould with water and pour it into a measuring cup to check the amount you need, 1ml equals roughly 1 gram. If you have a square or rectangle mould you can work out the volume by multiplying length by width by height.)
Cut the soap base into smaller blocks, about 1x1cm and place them in the jug.
Place the jug with the soap base into the microwave and heat in maximum 45 second bursts, stirring in between. Alternatively melt the soap in a melting pot/double boiler on medium heat, stirring often. Make sure you don’t overheat/boil the base. The normal temperature of soap that has melted properly is roughly 60 degrees Celsius. Once all the soap blocks have melted completely, stir the mixture gently. The time period the soap base takes to melt will depend on the amount you use and if you are using a microwave, the wattage of the microwave will also make a difference in time.
At this point you can add your colour. Use liquid soap dye or mica powders. Please read the individual instructions for colour and fragrance below.
Liquid: If you use liquid soap dye, add 1 drop at a time and stir gently, until you are happy with your colour. Liquid colours do tend to bleed into each other, so it is not ideal for colour layering.
Mica Powder: If you are using mica, take a popsicle stick or spoon and take a tiny bit of mica (depending on how strong you want the colour) and put it in a small mixing container. Add a few drops of Isopropyl alcohol (IPA) and mix thoroughly. The reason we disperse the mica in alcohol first is to avoid the mica powder clumping together which will result in an uneven colour or clumps of colour in your final soap. Add this mixture into the soap, little by little, until you have achieved the colour you need. Stir well, but gently. Vigorous stirring can cause bubbles.
After the colour is added, add your fragrance. The normal usage rate of fragrance oils in melt and pour is 1%. This would mean, if using 1000ml of melted base, you would add 10ml of fragrance. This may vary from different suppliers and manufacturers, so always check each supplier’s usage rate first on the IFRA fragrance document and always make sure the fragrance oil is skin safe. You can also use essential oils. Using a pipette, draw the necessary amount of fragrance from the bottle and drop it into the soap. Stirring gently for about 20 seconds will ensure that the fragrance oil has been blended in properly.
Spray your mould with a little spritz of Isopropyl alcohol (this helps the soap to adhere nicely to the mould and gets rid of surface tension making sure no bubbles are trapped between the soap and the mould)
Pour your soap gently into the mould. Spritz the top with rubbing alcohol as well to get rid of any bubbles.
Wait until your soap sets up completely before removing it from the mould. This can take 30 minutes up to several hours depending on the size of your mould. Once your soap is set, remove from the mould and wrap the soap in plastic film (like glad wrap) or shrink wrap as soon as possible after un-moulding. Glycerine is a humectant drawing moisture from the air to itself, which is why it is moisturising for your body, but unfortunately also causes the soap to draw the moisture from the air, causing glycerine dew drops on the soap. This is also known as sweating.

Disclaimer

The information provided is intended for general informational purposes only. While every effort has been made to ensure accuracy and correctness, it does not constitute a guarantee regarding any specific product properties. Users are responsible for verifying the suitability of products for their intended purposes. The Supplier reserves the right to update product information as necessary due to technical, production, or other developments without prior notice.
The availability of our products and/or services may change without notice. If a product is unavailable when you place an order, we will strive to provide information on its expected availability.
SA Candle Supply is not liable for any claims or damages arising from products that are out of stock or otherwise unavailable. We reserve the right to discontinue the sale of any product or service at any time without notice.
SACS may offer Product Information, including technical details, specifications, recommendations, literature, and other materials (collectively "Product Information") for customer convenience. The accuracy or completeness of Product Information is not guaranteed and is subject to change without notice; individual testing with our products is always necessary.
Products are not manufactured or reserved based on customer requirements or specifications unless explicitly agreed upon in writing by SACS.
SA Candle Supply is not responsible for any production flaws in the final product.
As the customer, you are responsible for providing usage and safety information labels and information to your clients.
Full Terms & Conditions Apply: https://sacandlesupply.co.za/terms-and-conditions/

Care & Caution

Prioritise safety by wearing goggles and gloves during product preparation.

Access the Safety Data Sheet (SDS) for comprehensive safety & product guidelines.

Exercise caution when working with any warm wax/oil and butter products. Use it exclusively within recommended applications.
Take care to avoid damage to polished, painted, plastic, or leather surfaces when producing any candles or body products. Follow instructions diligently.
Store the product out of reach of children and pets. Individuals with perfume sensitivity should use the product cautiously, it is advisable to make use of a safety mask.
Refrain from using this product for any other application than recommended.
Own testing is required.