Wave Cone Dinner Mould (22.8cm)

R220.00

Try this beautiful mould with 1 of our recommended recipes!

GLOSS PILLAR CANDLE RECIPE

RUSTIC PILLAR CANDLE RECIPE

SOY-PARAFFIN PILLAR CANDLE RECIPE

Strictly no returns on all moulds!

View product details below!

Out of stock

Out of stock

Or split into 4x interest-free payments Learn more
Categories: , ,
 
Description
Specifications:
How to use:
Wick: Selection & Use
Care & Caution:
Disclaimer:

Description

This taper top, tall PC Mould creates an elegant sturdy pillar, due to the diameter of the candle.

Our plastic candle moulds are made of high quality pc material. It can withstand frequent usage due to its resistance to high and low temperatures.

How to use the PC Moulds

Note that these instructions are based on our in-house testing. You should also explore the handling sheet, and conduct your own testing with fragrance loads, colouring and temperatures (download the complimentary testing sheet). Use the recommended fragrance load per wax type you are using in the moulds. We advise using a digital thermometer to measure the correct temperature of the wax to ensure optimal performance.

Specifications:

Specifications:

Wave Cone Dinner Mould (22.8cm) (1495)

Material: Polycarbonate

Estimated Mould Dimensions: 22.8cm(H) X 3.8cm (W)

Candle Dimensions: 22.5 H x 3cm W

 

Candle Weight: 125g

Fill Volume: approx. 135ml

LX Wick Suggestions: LX8

Own Testing is required.

How to use:

Prepare the mould by selecting the correct wick according to the provided chart on the LX wick range. Measure the wick length, and cut the wick accordingly.

Depending on the mould, pull the wick through the opening of the mould. Secure the wick with a small piece (ball) of either Prestik or our moulding clay to stick it into place and to “seal” it. Remember this will be the top of the candle. Thereafter thread the wick through a placeholder at the top of the mould. You might have to remove the placeholder while pouring and place over the mould again to secure into place.

Lay down some newspaper because pouring any type of candles can be messy. Ensure that you work on a sturdy surface and your candle wicks are firmly in place. Note that the volume of the mould will differ from wax and pouring, one to the next as the fill line is to the top, but the candle might shrink depending on the blend.

Follow the step by step instructions available on each of the applicable waxes.

*Note that these instructions are based on our in-house testing. You should also explore the handling sheet, and conduct your own testing with fragrance loads, colouring and temperatures (download the complimentary testing sheet). We use the recommended fragrance load per wax you are using in the moulds, using our fragrance range.  We advise using a digital thermometer to measure the correct temperature of the wax.

 

Unmoulding the PC candles

  • Leave the candles to dry completely for at least 12 hours. The mould should be completely cold and the wax completely set.
  • Remove the Prestik or moulding clay seal, gently shake or tap the mould to release the wax from the sides, turn around, and gently remove the candle.
  • Trim the wick off the base side of the candle, leaving the wick on the top end long before trimming.
  • If the pillar candle is uneven, heat up a pan on the stove and melt the bottom till it is even and can stand.

Wick: Selection & Use

LX WICKS

Select the correct wick size from the chart to use in moulded candle making. Note that we sell the sustainers separately for these wicks and self-assembly is required, where applicable on the specific product.

Measure the length of the wick needed by placing the mould next to it, keep at least 4-5cm available at each of the ends, to ensure that then threading the wick, there is ample length on each side to secure the wick into place.

Care & Caution:

  • If the Prestik / moulding clay lifts up the mould ( where you are ensuring a seal where the wick was threaded through, use strong packaging tape, and tape over this instead of the Prestik option.
  • You might have to top up with these moulds with wax due to paraffin wax’s shrinking characteristic. Keep a close eye on how the wax is drying, as sink holes might appear, and needs to be filled ( topped up)
  • If these sink holes appear, use a bbq stick to poke small holes around the wicks into the wax, to ensure the top up fills the cavities and ensures binding of the top up pour.
  • Use the same spaces where the initial holes was made for next use to avoid creating new holes in the mould, silicone is a great sealer, and should not seep wax, but be sure to seal with the tape. As mentioned above.
  • With Paraffin wax, you can do up to three pours to avoid and cavities in the candle, and to secure the smooth top.

Disclaimer:

Screen images are intended as a guide only and should not be regarded as absolutely correct.

Availability of our products and/or services is subject to change without notice. If a product is not in stock when you place your order, we will do our best to advise you when the product will be available.

SA Candle Supply shall not be liable for any claims or damages arising in connection with products which are out of stock or otherwise unavailable. SA Candle Supply reserves the right to discontinue the sale of any product or service at any time without notice to you or any other third party.

SACS may provide Product information, including technical information, specifications, recommendations, literature, and other materials (collectively “Product Information”) for Customer’s convenience.  The accuracy or completeness of Product Information is not guaranteed and is subject to change without notice.

Products are not manufactured to any Customer requirements or specifications unless expressly agreed to in writing by SACS.