We use cookies to make your experience better. To comply with the new e-privacy directive, we need to ask for your consent to set the cookies. Read our Cookie Policy.
PC Mould - Wave Tapered Dinner Mould Thin
In stock
SKU
pcwtdt
R 180.00
This tapered, tall PC Mould creates an elegant dinner pillar, due to the diameter of the candle.
These candle moulds are made of high quality Polycarbonate material. It can withstand frequent usage due to its resistance to high and low temperatures.
Wave Tapered Dinner Mould Thin is supplied as 2 pieces.
Material: Polycarbonate
Estimated Mould Dimensions: 25cm(H) X 2.2cm (W)
Candle Dimensions: 25cm (H) x 2.1cm (W
Candle Weight: Approx. 65g
Fill Volume: Approx. 70ml
LX Wick Suggestions: LX8
Own Testing is required.
Prepare the mould by selecting the correct wick according to the provided chart on the LX wick range. Measure the wick length, and cut the wick accordingly.
- Depending on the mould, pull the wick through the opening of the mould, at the base.
- Secure the wick with a small piece (ball) of either Prestik or our moulding clay to stick it into place and to “seal” it. Remember this will be the top of the candle.
- Thereafter thread the wick through a placeholder at the top of the mould. You might have to remove the placeholder while pouring and place over the mould again to secure into place.
- Lay down some newspaper as pouring any type of candles can be messy.
- Ensure that you work on a sturdy surface and your candle wicks are firmly in place.
- Note that the volume of the mould will differ from wax types.
- Pour to the fill line at the top, keep in mind that the candle might shrink depending on the wax blend selected.
- Follow the step by step instructions available on each of the applicable waxes.
Un-moulding the PC candles
- Leave the candles to cure completely for at least 12 hours.
- The mould should be completely cold and the wax completely set.
- Remove the Prestik or moulding clay seal, gently shake or tap the mould to release the wax from the sides, turn around, and gently remove the candle.
- Trim the wick off the base side of the candle, leaving the wick on the top end long before trimming.
- If the pillar candle is uneven, heat up a pan on the stove and melt the bottom till it is even and can stand. ( do not use the same pan for any cooking)
Special Note: These instructions are based on our in-house testing. You should also explore the handling sheet, and conduct your own testing with fragrance loads, colouring and temperatures
We use the recommended fragrance load per wax you are using in the moulds, using our fragrance range. We advise using a digital thermometer to measure the correct temperature of the wax.
- The information provided is intended for general informational purposes only. While every effort has been made to ensure accuracy and correctness, it does not constitute a guarantee regarding any specific product properties. Users are responsible for verifying the suitability of products for their intended purposes. The Supplier reserves the right to update product information as necessary due to technical, production, or other developments without prior notice.
- The availability of our products and/or services may change without notice. If a product is unavailable when you place an order, we will strive to provide information on its expected availability.
- SA Candle Supply is not liable for any claims or damages arising from products that are out of stock or otherwise unavailable. We reserve the right to discontinue the sale of any product or service at any time without notice.
- SACS may offer Product Information, including technical details, specifications, recommendations, literature, and other materials (collectively "Product Information") for customer convenience. The accuracy or completeness of Product Information is not guaranteed and is subject to change without notice; individual testing with our products is always necessary.
- Products are not manufactured or reserved based on customer requirements or specifications unless explicitly agreed upon in writing by SACS.
- SA Candle Supply is not responsible for any production flaws in the final product.
- As the customer, you are responsible for providing usage and safety information labels and information to your clients.
- Full Terms & Conditions Apply: T & C
- Prioritise safety by wearing goggles and gloves during product preparation.
- Access the Safety Data Sheet (SDS) for comprehensive safety & product guidelines.
- Exercise caution when working with any warm wax products. Use it exclusively within recommended applications.
- Take care to avoid damage to polished, painted, plastic, or leather surfaces when producing any candles or body products. Follow instructions diligently.
- Store the product out of reach of children and pets. Individuals with perfume sensitivity should use the product cautiously, it is advisable to make use of a safety mask.
- Refrain from using this product for any other application than recommended.
- Own testing is required.
Related Products
Check items to add to the cart or
We found other products you might like!
-
PC Mould - Wave Cone Dinner 22.8cmR 220.00 -
Silicone Mould - Fluted Dinner 23.8 x 4.5cmSpecial Price R 100.00 Regular Price R 160.00 -
Silicone Mould - Wave Dinner 24.8 x 4cmSpecial Price R 100.00 Regular Price R 160.00 -
Silicone Mould - Cubist Dinner 24.7x4.8cmSpecial Price R 100.00 Regular Price R 180.00
