We use cookies to make your experience better. To comply with the new e-privacy directive, we need to ask for your consent to set the cookies. Read our Cookie Policy.
Silicone Mould - Honeycomb Hexagon 9.5 x 7cm
In stock
SKU
smhohx
R 250.00
The Honeycomb Hexagon Silicone mould is a lovely casting stencil for making ornamental candles for your house.
Our silicone moulds are made of high-quality, non-toxic, and heat-resisting silicone. This reusable and durable candling mould is easy to use and convenient to handle. These moulds are formed of elastic and reusable materials that mould and de-moulds the candle perfectly.
The Honeycomb Hexagon Silicone mould is a lovely casting stencil for making ornamental candles for your house. The mould is composed of high-quality silicone, which makes it extremely durable and easy to use. A convenient and stylish honeycomb design which creates a stunning decorative candle.
This Candle Mould can be used as for soap making as well.
- Material: Silicone
- Estimated Mould Dimensions: 9.5cm(H) x 7 cm(W)
- Candle Dimensions: 8cm (H) X 5cm (W)
- Candle Weight: 110g
- Fill Volume: Approx 119ml
- LX Wick Suggestions: LX10
- Own Testing is required.
Prepare the mould by selecting the correct wick according to the provided chart on the LX wick range. Measure the wick length, and cut the wick accordingly.
- Using a tapestry needle (one with a large eye) , thread the pre measures wick through the eye, then finding the centre of the silicone mould, gently piece a hole through, pulling the wick through with it.
- Secure the wick with a small piece ( ball ) either Prestik, our moulding clay, to stick it into place, and to “seal” it, remember this will be the top of the candle.
- Thereafter thread the wick through a placeholder at the top of the mould, you might have to remove the placeholder while pouring and place over again after to secure into place.
- Lay down some newspaper because pouring any type of candles can be messy.
- Ensure that you work on a sturdy surface and your candle wicks are firmly in place. Note that the volume of the mould will differ from wax and pouring, one to the next as the fill line is to the top, but the candle might shrink depending on the blend.
- Follow the step by step instructions available on each of the applicable waxes. For moulded candles we recommend either Paraffin Wax or Eco Pillar Soy Wax
Special Note:
These instructions are based on our in-house testing. You should also explore the handling sheet, and conduct your own testing with fragrance loads, colouring and temperatures (download the complimentary testing sheet). We use the recommended fragrance load per wax you are using in the moulds, using our fragrance range. We advise using a digital thermometer to measure the correct temperature of the wax.
Un-moulding the Silicone candles
- Leave the candles to dry completely for at least 12 hours. The mould should not be warm at all, and the wax completely set.
- Remove the Prestik / moulding clay seal / tape seal, gently pull at the sides to loosen, then peel back the silicone, and gently pull the wicks through the holes made with the needles turn around, and gently remove the candle.
- Trim the wick off the base side of the candle, leaving the wick on the top shaped end before trimming.
- The information provided is intended for general informational purposes only. While every effort has been made to ensure accuracy and correctness, it does not constitute a guarantee regarding any specific product properties. Users are responsible for verifying the suitability of products for their intended purposes. The Supplier reserves the right to update product information as necessary due to technical, production, or other developments without prior notice.
- The availability of our products and/or services may change without notice. If a product is unavailable when you place an order, we will strive to provide information on its expected availability.
- SA Candle Supply is not liable for any claims or damages arising from products that are out of stock or otherwise unavailable. We reserve the right to discontinue the sale of any product or service at any time without notice.
- SACS may offer Product Information, including technical details, specifications, recommendations, literature, and other materials (collectively "Product Information") for customer convenience. The accuracy or completeness of Product Information is not guaranteed and is subject to change without notice; individual testing with our products is always necessary.
- Products are not manufactured or reserved based on customer requirements or specifications unless explicitly agreed upon in writing by SACS.
- SA Candle Supply is not responsible for any production flaws in the final product.
- As the customer, you are responsible for providing usage and safety information labels and information to your clients.
- Full Terms & Conditions Apply: T & C
- Prioritise safety by wearing goggles and gloves during product preparation.
- Access the Safety Data Sheet (SDS) for comprehensive safety & product guidelines.
- Exercise caution when working with any warm wax products. Use it exclusively within recommended applications.
- Take care to avoid damage to polished, painted, plastic, or leather surfaces when producing any candles or body products. Follow instructions diligently.
- Store the product out of reach of children and pets. Individuals with perfume sensitivity should use the product cautiously, it is advisable to make use of a safety mask.
- Refrain from using this product for any other application than recommended.
- Own testing is required.